Gear Standards

Gear StandardsGear StandardsGear StandardsGear StandardsGear StandardsGear Standards

ISO TC 60

Standard NoStandard
ISO 53:1998Cylindrical gears for general and heavy engineering — Standard basic rack tooth profile
ISO 54:1996Cylindrical gears for general engineering and for heavy engineering — Modules
ISO 677:1976Straight bevel gears for general engineering and heavy engineering — Basic rack
ISO 678:1976Straight bevel gears for general engineering and heavy engineering — Modules and diametral pitches
ISO 1328-1:2013Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth
ISO 1328-2:1997Cylindrical gears — ISO system of accuracy — Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information
ISO 8579-1:2002Acceptance code for gear units — Part 1: Test code for airborne sound
ISO/TR 10064-1:1992Code of inspection practice — Part 1: Inspection of corresponding flanks of gear teeth
ISO/TR 10064-1:1992/Cor 1:2006Code of inspection practice — Part 1: Inspection of corresponding flanks of gear teeth
ISO/TR 10064-2:1996Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash
ISO/TR 10064-2:1996/Cor 1:2001Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash
ISO/TR 10064-2:1996/Cor 2:2006Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash
ISO/TR 10064-3:1996Code of inspection practice — Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes
ISO/TR 10064-3:1996/Cor 1:2006Code of inspection practice — Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes
ISO/TR 10064-4:1998Code of inspection practice — Part 4: Recommendations relative to surface texture and tooth contact pattern checking
ISO/TR 10064-4:1998/Cor 1:2006Code of inspection practice — Part 4: Recommendations relative to surface texture and tooth contact pattern checking
ISO/TR 10064-5:2005Code of inspection practice — Part 5: Recommendations relative to evaluation of gear measuring instruments
ISO/TR 10064-5:2005/Cor 1:2006Code of inspection practice — Part 5: Recommendations relative to evaluation of gear measuring instruments
ISO/TR 10064-6:2009Code of inspection practice — Part 6: Bevel gear measurement methods
ISO 17485:2006Bevel gears — ISO system of accuracy
ISO 18653:2003Gears — Evaluation of instruments for the measurement of individual gears
IEC 61400-4:2012Wind turbines — Part 4: Design requirements for wind turbine gearboxes

NOMENCLATURE

Standard NoStandard
ISO 701:1998International gear notation — Symbols for geometrical data
ISO 1122-1:1998Vocabulary of gear terms — Part 1: Definitions related to geometry
ISO 1122-1:1998/Cor 1:1999Vocabulary of gear terms — Part 1: Definitions related to geometry
ISO 1122-1:1998/Cor 2:2009Vocabulary of gear terms — Part 1: Definitions related to geometry
ISO 1122-2:1999Vocabulary of gear terms — Part 2: Definitions related to worm gear geometry
ISO 2490:2007Solid (monobloc) gear hobs with tenon drive or axial keyway, 0,5 to 40 module — Nominal dimensions
ISO 4468:2009Gear hobs — Accuracy requirements
ISO 4468:2009/Cor 1:2009Gear hobs — Accuracy requirements
ISO 10825:1995Gears — Wear and damage to gear teeth — Terminology
ISO/TR 10828:2015Worm gears — Worm profiles and gear mesh geometry
ISO/TR 14521:2010Gears — Calculation of load capacity of wormgears
ISO 21771:2007Gears — Cylindrical involute gears and gear pairs — Concepts and geometry

CALCULATION

Standard NoStandard
ISO 6336-1:2006Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors
ISO 6336-1:2006/Cor 1:2008Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors
ISO 6336-2:2006Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting)
ISO 6336-2:2006/Cor 1:2008Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting)
ISO 6336-3:2006Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength
ISO 6336-3:2006/Cor 1:2008Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength
ISO 6336-5:2016Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials
ISO 6336-6:2006Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load
ISO 6336-6:2006/Cor 1:2007Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load
ISO 9083:2001Calculation of load capacity of spur and helical gears — Application to marine gears
ISO 9085:2002Calculation of load capacity of spur and helical gears — Application for industrial gears
ISO 10300-1:2014Calculation of load capacity of bevel gears — Part 1: Introduction and general influence factors
ISO 10300-2:2014Calculation of load capacity of bevel gears — Part 2: Calculation of surface durability (pitting)
ISO 10300-3:2014Calculation of load capacity of bevel gears — Part 3: Calculation of tooth root strength
ISO 13691:2001Petroleum and natural gas industries — High-speed special-purpose gear units
ISO 14104:2017Gears — Surface temper etch inspection after grinding, chemical method
ISO/TR 14179-1:2001Gears — Thermal capacity — Part 1: Rating gear drives with thermal equilibrium at 95 °C sump temperature
ISO/TR 14179-2:2001Gears — Thermal capacity — Part 2: Thermal load-carrying capacity
ISO 14635-1:2000Gears — FZG test procedures — Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils
ISO 14635-2:2004Gears — FZG test procedures — Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of high EP oils
ISO 14635-3:2005Gears — FZG test procedures — Part 3: FZG test method A/2, 8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases
ISO/TR 15144-1:2014Calculation of micropitting load capacity of cylindrical spur and helical gears — Part 1: Introduction and basic principles
ISO/TR 15144-2:2014Calculation of micropitting load capacity of cylindrical spur and helical gears — Part 2: Examples of calculation for micropitting
ISO/TR 18792:2008Lubrication of industrial gear drives
ISO/TR 22849:2011Design recommendations for bevel gears
ISO 23509:2016Bevel and hypoid gear geometry

© Modulus Metal 2017-2022    |    All Rights Reserved